FDA Regulatory Compliance Training - Live Webinars, Recordings & CDs

In this FDA audit & Inspection training we will focus on ideas that will help identify areas of improvement before the formal inspection occurs. Further, you will learn techniques that will enhance your effectiveness during the audit execution.

This FDA audit & inspection training will provide your firm with key insights on how to perform superior supplier audits. It will help you uncover purchasing controls GMP violations.

This FDA compliance training will provide valuable assistance to all new & existing OTC drug firms that are regulated by FDA due to their domestic USA sales.

This FDA compliance training will be valuable who are involved in the development of REMS and who are planning a submission and need to understand what might be required by FDA and how to comply and for those who have Risk Management Plans.

This 21 CFR Part 11 training will deliver concrete guidance which will provide a roadmap for compliance that will have immediate benefits, withstand FDA’s changes to Part 11, and discuss the new Obama administration approach to enforcement.

The FDA Audit inspection training defines the laboratory environment; points out problem areas and common pitfalls; and details solutions and also details how to prepare the Laboratory staff for an Inspection as well.

This CAPA training will focus on defining the specific steps to be taken when implementing a CAPA system and review some of the possible pitfalls one may encounter when implementing a CAPA system. This presentation will begin by defining risk in compliance and the methods, which can be used to mitigate risk. One of the methods defined by the regulators and the industry is “Corrective Action Preventive Action” otherwise referred to CAPA. We will first define what we mean by risk. We will then explore the factors associated with risk in compliance. We will also explore risk causing events and how to address them. A review of risk severity/level will then ensue. Upon completion of risk part of the presentation we will define what a CAPA system would look like.

The presentation will focus on CAPA as it applies to risk mitigation. We will define what we mean by a CAPA system. We will further define the tools CAPA uses during implementation. Finally an overview of a CAPA system will be presented and a CAPA approach will be proposed. The approach will focus on defining the specific steps to be taken when implementing a CAPA system and review some of the possible pitfalls one may encounter when implementing a CAPA system. We will also review some of the benefits which may accrue by having a robust CAPA system in place.

This FDA GMP (Good Manufacturing Practice) inspection training will walk you through the elements you should plan for, the timing and the logistics of who should do the various components in preparation for the inspection.

This Cleaning validation training will provide valuable assistance to all regulated companies that need to develop and validate their equipment cleaning processes. This session will address risk-based approaches to cleaning validation studies using ICH Q9 and recent FDA comments and observations as a foundation. Recent FDA warning letters illustrate just how critical good cleaning practices are. Understanding and employing good cleaning practices are instrumental to improving cleaning consistency, quality and traceability. The FDA favors automated CIP systems since they reduce operator variability while enhancing consistency and reproducibility. Our research has indicated that in the last 5 years, cleaning citations were noted in 50% of warning FDA letters. Many cited contamination issues have an element of poor cleaning practices associated with them. Examples include “investigations…did not include an evaluation of the cleaning processes and procedures…to determine if equipment cleaning is effective in preventing cross contamination of the inactivated batches”, FDA Warning Letter, Jan 2008; "vaccine manufacturing plant in Pennsylvania, has been served with an FDA warning letter asking for measures to ensure batches of its flu shot ingredients do not become contaminated again.” Jul-2006..

An overview of ICH risk management techniques and how to apply them to equipment cleaning programs will be discussed. In addition, case studies from manufacturing facilities will be used to illustrate risk-based cleaning validation principles and practices.

This Medical device training will provide valuable assistance and guidance to device companies involved in labeling changes. FDA recently released a final rule regarding the parameters in which a device manufacturer can modify label changes to a product. Specifically, manufacturers can add or strengthen the contraindications, warnings, precautions or adverse reactions sections of labeling via a PMA supplement without prior FDA approval only when such modifications are based on newly acquired information and evidence of a causal association between the product and a safety signal is present. The rule also provides clarification as to what the Agency considers to be new information to be incorporated into a label change. Specifically, new information “must reveal risks of a different type or greater severity or frequency than previously included in submissions” and includes meta-analyses, the new regulation states.” FDA requires that drug, biologics, and medical device manufacturers obtain FDA approval of their warning labels before the drugs or devices are marketed and sold. Manufacturers generally must also obtain FDA approval before making changes to labeling information. However, in limited circumstances, companies can revise or supplement their warning labels prior to FDA approval (through changes being effected (CBE) supplements) to ensure consumers are immediately made aware of newly discovered risks.

The labeling regulations, which became effective in late September 2008, clarify that a manufacturer can make unilateral pre-FDA approved labeling changes “only to reflect newly acquired information” when there is “reasonable evidence of a causal association” between the drug or device and the risk. The final rule defines “newly acquired information” as “information not previously submitted to [the] FDA.” This includes “new analyses of previously submitted data,” such as adverse event reports, new clinical study information, and new analyses that “reveal risks of a different type or greater severity or frequency than previously included in submissions to [the] FDA. Under the final rule, however, a CBE supplement is available only if there is "sufficient evidence of a causal association" justifying the addition or strengthening of a contraindication, warning, precaution or adverse reaction. The FDA explains that the language "sufficient evidence of a causal association" refers to the standards for drugs and biologics set forth in §201.57(c)(6) and §201.57(c)(7).

This FDA compliance training will describe the essential requirements for producing sterile products in a practical, clear, concise manner that will facilitate its implementation.

This FDA Inspection training will examines the audit process and how to manage Process Deviation Investigations.

This course on Implementing Human Factors in Manufacturing provides a comprehensive overview of how to integrate human factors principles into manufacturing processes to reduce errors, improve safety and quality, and enhance operational efficiency. Participants will learn about the types and causes of human errors, ergonomic design principles, human-machine interface optimization, and effective strategies for fostering a culture of safety, quality, and continuous improvement. Through interactive workshops, case studies, and practical applications, attendees will gain the tools needed to conduct human factors assessments, design effective training programs, and develop actionable plans for sustainable improvement in their organizations.

This Validation training will explain the intent and importance of process validation. Process validation is critical to the production of high quality, consistent, safe and effective products and devices. Routine end-product testing alone is insufficient to assure the quality, safety and effectiveness of a product or device. It is important that the product acceptance criteria and specifications are quantified, and that the manufacturing processes are well characterized, understood, controlled and validated.

This Process Validation training will detail the key qualification steps in process validation, the use of statistical methodology for sampling plans and acceptance criteria, how to handle deviations, elements of a good validation summary report. Process validation is critical to the production of high quality, consistent, safe and effective products and devices. Routine end-product testing alone is insufficient to assure the quality, safety and effectiveness of a product or device. It is important that the product acceptance criteria and specifications are quantified, and that the manufacturing processes are well characterized, understood, controlled and validated.

This Validation training will explain the intent and importance of process validation, the connectivity between design control and process validation and the key pre-requisites and steps in process validation. Process validation is critical to the production of high quality, consistent, safe and effective products and devices. Routine end-product testing alone is insufficient to assure the quality, safety and effectiveness of a product or device. It is important that the product acceptance criteria and specifications are quantified, and that the manufacturing processes are well characterized, understood, controlled and validated.

This webinar will provide invaluable assistance to investigators and their staff in the regulatory / legal responsibilities and also the ethical considerations in pharmaceutical product (Drug or device) research involving human subjects.

This Clinical Trial training will provide a detailed review of the FDA regulations for Clinical Trials Process. This presentation will provide a detailed review of the FDA regulations for Clinical Trials Process. After attending this session, participants will have an understanding of FDA regulations pertaining to the implementation of clinical trials and concepts of Good Clinical Practice (GCP) and Bioethics.

This GLP (Good Laboratory Practices) webinar reviews the process of closing a study by preparing a final report and managing all records and specimens in a proper manner. The GLP final study report represents the last chance for a study team to present their results in a clear and compelling manner. The report may also be a place where difficulties can be explained so that the study provides meaningful and trustworthy information. This webinar reviews the process of closing a study by preparing a final report and managing all records and specimens in a proper manner. It provides two areas of concentration: (1) the best practices in final report writing and (2) the step-by-step process of closing studies.

This presentation will give an overview of the FDAAA and summarize the new provisions pertaining to specialized pediatric medical device development, food safety, advisory committee provisions, clinical trial registries and drug safety enhancement.